Contact lamellae
Louvered contact bands with many parallel contact points
Contact lamellae
The leaf spring contact band, also known as leaf spring contact, crown spring contact or leaf spring lamella, is the compact contact lamella for power and signal contacts from 1.5 mm mating diameter. Pre-rounded from beryllium copper, made in Wehr (Baden), Germany.
Drag to rotate, scroll or pinch to zoom. Keyboard: arrow keys rotate, plus and minus zoom, 0 resets the view.
01 Principle
In the leaf spring contact band the louvers (contact webs) are loaded in bending, like many small leaf springs side by side. A blank with parallel longitudinal slots is stamped, leaving a continuous edge strip at each end. When the blank is rolled, the edge strips become rings and the louvers form a spring basket that presses against the mating contact with a preload.
Leaf spring contacts carry power as well as signals. They are compact and have very good electrical properties. The standard sizes start at 1.5 mm mating diameter for the socket version and at 2 mm for the pin version. Leaf spring contacts therefore cover the small diameters for which the torsion spring contact band is not intended.
We make these contact lamellae from relaxation-resistant beryllium copper and supply them pre-rounded to the required diameter. Qualified partners apply the nickel, silver or gold finish. All you need is a turned part, a pin or a socket, to hold them. The standard range is available in the configurator. We make other sizes to your specification.
02 Versions
The leaf spring contact band comes in two versions: the pin version sits in a groove on the pin, the socket version in an internal groove of the socket.
Pin version: The louvers bow outwards. The lamella sits in a groove on the pin and contacts the cylindrical bore of the socket.
Socket version: The louvers bow inwards, giving the lamella a waisted shape. It sits in an internal groove (recess) in the socket and contacts a cylindrical pin.
In both cases the lamella is pushed into the groove, where it snaps in and is held captive. The fits for bore and pin are the same. The groove diameter depends on the material thickness S.
03 Technical data
| Property | Value |
|---|---|
| Mating diameter D | from 1.5 mm (socket version), pin version from 2 mm in the standard sizes |
| Length L (standard sizes) | 5 / 8 / 12 mm |
| Material | Beryllium copper (CuBe), relaxation-resistant |
| Finish | nickel, silver or gold, bare on request |
| Standard range, pin version | D 2–8 mm, L 8 or 12 mm, S 0.15–0.2 mm |
| Standard range, socket version | D 1.5–16 mm, L 5, 8 or 12 mm, S 0.1–0.2 mm |
| Socket bore | D +0.05 mm |
| Pin diameter | D −0.03 mm |
| Groove diameter in the socket | D + 0.7 mm (S = 0.2 mm), D + 0.6 mm (S = 0.15 mm), D + 0.5 mm (S = 0.1 mm) |
| Groove diameter on the pin | D − 0.7 mm (S = 0.2 mm and 0.17 mm), D − 0.5 mm (S = 0.15 mm) |
| Groove width | L +0.25 mm |
| Delivery form | pre-rounded to diameter, ready to install |
| Contact resistance, contact force, insertion force | on request |
| Current rating of the lamella (guide value) | I ≈ k × D (D in mm), nickel-plated. Pin k = 9 / 10.5 / 12 A for S = 0.15 / 0.17 / 0.2 mm, socket k = 6 / 10.5 / 14 A for S = 0.1 / 0.15 / 0.2 mm. Silver- or gold-plated × 1.2 |
| Temperature range | on request |
| Mating cycles | on request |
Values from the installation drawings and the lamella configurator. Electrical values (contact resistance, contact force, temperature range) are available on request. The current rating is a guide value from the configurator and depends on the installation, so higher or lower values are possible.
Last updated:
04 Standard sizes, pin
Dimensions in mm · L = length · S = material thickness · guide current in A: Ni/Ag, Au
| Criterion | L | S | Groove Ø | Groove width | Guide value A |
|---|---|---|---|---|---|
| D 2 mm | 8 | 0.15 | 1.5 | 8 +0.25 | 18/22 |
| D 3 mm | 8 | 0.15 | 2.5 | 8 +0.25 | 27/33 |
| D 4 mm | 8 | 0.17 | 3.3 | 8 +0.25 | 42/51 |
| D 4 mm | 12 | 0.2 | 3.3 | 12 +0.25 | 48/58 |
| D 6 mm | 12 | 0.2 | 5.3 | 12 +0.25 | 72/87 |
| D 8 mm | 12 | 0.2 | 7.3 | 12 +0.25 | 96/120 |
Material CuBe. Socket bore D +0.05 mm. Groove diameter and width calculated from the installation drawings (D − 0.7 for S = 0.2 and 0.17, D − 0.5 for S = 0.15, groove width L +0.25). Guide value of the current rating of the whole lamella from the lamella configurator, nickel-plated or silver- or gold-plated, rounded as in the configurator: to whole amps below 100 A, to the nearest 10 A from 100 A. Depending on the installation, higher or lower values are possible.
05 Standard sizes, socket
Dimensions in mm · L = length · S = material thickness · guide current in A: Ni/Ag, Au
| Criterion | L | S | Groove Ø | Groove width | Guide value A |
|---|---|---|---|---|---|
| D 1.5 mm | 5 | 0.1 | 2.0 | 5 +0.25 | 9/11 |
| D 2 mm | 5 | 0.1 | 2.5 | 5 +0.25 | 12/15 |
| D 3 mm | 12 | 0.2 | 3.7 | 12 +0.25 | 42/51 |
| D 4 mm | 8 | 0.15 | 4.6 | 8 +0.25 | 42/51 |
| D 4 mm | 12 | 0.2 | 4.7 | 12 +0.25 | 56/67 |
| D 5 mm | 8 | 0.15 | 5.6 | 8 +0.25 | 53/63 |
| D 6 mm | 8 | 0.15 | 6.6 | 8 +0.25 | 63/76 |
| D 6 mm | 8 | 0.2 | 6.7 | 8 +0.25 | 84/100 |
| D 8 mm | 8 | 0.2 | 8.7 | 8 +0.25 | 110/130 |
| D 8 mm | 12 | 0.2 | 8.7 | 12 +0.25 | 110/130 |
| D 10 mm | 8 | 0.2 | 10.7 | 8 +0.25 | 140/170 |
| D 10 mm | 12 | 0.2 | 10.7 | 12 +0.25 | 140/170 |
| D 12 mm | 12 | 0.2 | 12.7 | 12 +0.25 | 170/200 |
| D 16 mm | 8 | 0.15 | 16.6 | 8 +0.25 | 170/200 |
| D 16 mm | 12 | 0.2 | 16.7 | 12 +0.25 | 220/270 |
Material CuBe. Pin diameter D −0.03 mm. Groove diameter and width calculated from the installation drawings (D + 0.7 for S = 0.2, D + 0.6 for S = 0.15, D + 0.5 for S = 0.1, groove width L +0.25). Current guide values from the lamella configurator, as for the pin version and rounded the same way. Other sizes on request.
06 Advantages
Short lamellae of 5 to 12 mm length and small diameters from 1.5 mm fit into tight connectors.
The same design carries power currents and signals, with very good electrical properties.
The lamella arrives rolled to your diameter. You only make the turned part with the groove.
Nickel for standard applications, silver for high currents, gold where corrosion resistance is critical.
We make leaf spring contacts in large and small quantities.
If your size is not in the table, we design the lamella to your drawing.
07 Finishes
CuBe
Relaxation-resistant spring material that keeps its contact force over a long service life. We make the leaf spring contact band exclusively from beryllium copper.
Ni
For standard applications.
Ag
For high currents.
Au
Where corrosion resistance is critical.
08 Applications
Small mating diameters for signal and supply contacts in medical devices.
Test plugs and test probes with lamella contacts.
Connectors for power transmission in the field.
Power and signal contacts in charging plugs.
Circular connectors on machines and installations.
Pluggable contacts in automation and welding equipment.
09 Configurator
The lamella configurator calculates a guide value for the current rating of every standard size of the leaf spring contact band. Choose pin or socket version, mating diameter, length, material thickness and finish. The configurator also shows a dimensioned sketch.
10 Downloads
FAQ
The standard range of the leaf spring contact band comprises 21 sizes, all stored in the lamella configurator: 6 pin-version sizes from 2 to 8 mm and 15 socket-version sizes from 1.5 to 16 mm mating diameter, each with a length L of 5, 8 or 12 mm. The tables on this page list them with groove dimensions. We will give you lead time and price with the quotation.
Yes. Send us the mating diameter, the length you need and your installation, ideally with a drawing. We also make leaf spring contacts outside the standard sizes.
For the socket version the groove diameter is D + 0.7 mm at S = 0.2 mm, D + 0.6 mm at S = 0.15 mm and D + 0.5 mm at S = 0.1 mm. For the pin version it is D − 0.7 mm at S = 0.2 and 0.17 mm and D − 0.5 mm at S = 0.15 mm. The groove width is L +0.25 mm. Bore D +0.05 mm, pin D −0.03 mm.
That depends on diameter, material thickness, finish and installation. As a guide value, I ≈ k × D with D in mm, for example k = 14 A for the nickel-plated socket version with S = 0.2 mm, and 1.2 times that with silver or gold. The guide values of every standard size are in the tables on this page and in the lamella configurator. Depending on the installation, higher or lower values are possible, so please verify the value in your application.
Nickel is sufficient for standard applications. Choose silver for high currents and gold where corrosion resistance is critical.
Request a quote
Pick a standard size directly in the configurator above. For special sizes, send us your drawing with mating diameter, length, finish and quantity.