Materials and finishes
Copper alloys, spring steels and contact platings compared
Services
Silver, tin, gold or nickel, all-over or selective, and zinc for steel parts: ACA Atlas Contacte in Wehr (Baden), Germany, supplies stamped and bent parts and electrical contacts with the electroplated finish your application requires. Qualified plating partners apply the coating, ACA coordinates the process and delivers the finished part.
01 Overview
On an electrical contact, the plated finish determines how well current flows across the contact point, how many mating cycles the part withstands and how it responds to humidity, heat and corrosive gases. The base material provides spring force and conductivity, the coating protects the contact point and keeps contact resistance low.
ACA does not plate in-house. We work with qualified plating partners and take care of selection, specification, logistics and coordination with the stamping process for you. You order a finished, plated stamped part from one supplier. Age-hardening of beryllium copper, for example for our contact lamellae, is done in-house.
02 Finishes
Ag
For high-current contacts: low contact resistance and high current-carrying capacity. On our high-current contact band the copper contact pieces are silver-plated and passivated, on our torsion spring contact band the whole band. Silver tarnishes in sulphur-bearing atmospheres, and passivation slows this down.
Sn
An economical finish for plug and solder connections with few mating cycles. Readily solderable and protective against corrosion, but prone to fretting corrosion when the contact point is exposed to micro-movement.
Au
For contacts that need high corrosion resistance and for signal contacts with low currents and contact forces. Because of its price it is usually applied selectively to the contact zone, normally over a nickel underlayer.
Ni
For standard applications and as a barrier layer and underlayer beneath gold. Hard and wear-resistant, with a higher contact resistance than silver or gold.
Zn
Corrosion protection for stamped parts made of steel. Zinc protects the steel cathodically, even where the coating is slightly damaged, and is usually passivated as well. Zinc is not a usual contact surface. Like all other finishes, ACA supplies zinc-plated parts through its plating partners.
bare
Not every part needs a coating. The torsion spring contact band, for example, is available silver-plated or alternatively bare. Whether your part can stay bare depends on material, environment and contact function.
03 Selective plating
Selective plating means that only the contact zone of a part is coated with precious metal. The rest stays bare or receives a simpler coating. This saves gold or silver, and therefore cost, without changing the contact function. On press-fit pins, for example, the mating end can carry gold and the press-fit zone tin.
On parts made from strip, plating can be limited to stripes or zones of the strip. For this to work, contact zone and strip layout have to match. We define both together before the tool is built. Electroplated and selectively plated strip are part of our range.
04 Sequence
| Criterion | Plated or clad strip | Plating after stamping |
|---|---|---|
| Sequence | The strip arrives plated or clad and is then stamped and bent. | The parts are stamped and bent and then electroplated. |
| Cut edges | remain uncoated | are coated as well |
| Bend zones | The coating is formed together with the part, so the bend radius must suit the coating. | The coating is applied after bending and is not formed again. |
| Points to watch | specify material and coating as a semi-finished product | coating thickness distribution at edges and in inside corners |
ACA also makes stamped parts from clad strip and contact profiles. We choose the route with you and the plating partner.
05 Specification
A clear finish specification on the drawing saves questions and extra sampling rounds. The more precise it is, the more reliably the plating partner can reproduce the coating. Background on materials and coatings is in our guide to materials and finishes.
FAQ
No. ACA Atlas Contacte has electroplated finishes such as silver, tin, gold, nickel and zinc applied by qualified plating partners. ACA coordinates specification, plating and logistics and delivers the finished, plated part from one source. Age-hardening of beryllium copper, by contrast, is done in-house at ACA.
Coating thickness depends on application, mating cycles and environment and is set to the customer's specification. An example from the range of ACA Atlas Contacte: on the high-current contact band the silver layer is 20 µm as standard and is chosen to suit the application.
With selective plating only the contact zone of a stamped part is coated with a precious metal such as gold or silver, while the rest stays bare or receives a simpler coating. This reduces precious metal consumption without impairing the contact function.
Precious metal, for example for an electroplated coating, is charged under the general terms of sale (AVB) of ACA Atlas Contacte, available as a PDF in German. ACA states the price of your plated part in the quotation.
On the torsion spring contact band from ACA Atlas Contacte the whole band is silver-plated and passivated, and it is also available bare. On the high-current contact band the copper contact pieces on the spring steel carrier are silver-plated and passivated. Leaf spring lamellae are available in nickel, silver or gold.
Request a quote
Tell us the base material, the required coating and thickness, the coated zone and the quantity. You will receive a quotation for the finished, plated part.